Kenmeri build part 3

admin

Posted on December 21 2009

In this part of the Kenmeri build I’m going to go into detail another part of this 73 Skyline that definitely needed some attention before we could consider it fit to be sold.  One of the most notable aesthetic features that distinguishes the GT-R from the standard model Skyline has to be the fender flares.  When we had received the car it came with some reproduction flares already on it, and from about 10 feet away everything looks peachy but it’s only when you move in for a closer inspection that things start to get ugly.   Now anyone who has ever bought any aftermarket body part (especially fiberglass) and prepped and installed it themselves will tell you that you usually get exactly what you pay for.  This rings especially true here.  Being that there is not an option to acquire OEM flares there is no other choice than to pick up an aftermarket reproduction.  There are a few options out there and this car definitely came with what I can only guess are reproductions of reproductions, and were painted and half screwed to the car with no regard for fitment or finish.   But wait,  it gets worse………..

10_9_09 087

Now other than the fact that the flares are partially screwed with a variety of philips and flat head and “whatever I could find around the garage floor” hardware, note the fact that you can see the original fender underneath the flare.  This was the case on all 4 fenders.  Other than it looking ridiculous, it kind of defeats the purpose of installing flares in the first place,  to fit wider wheels and more rubber.   Instead of trying to salvage the existing flares, we decided to import a set of high quality FRP reproductions from Japan.  After waiting a couple of weeks for the flares to arrive it was now time to remove the old ones and properly modify the factory metal fenders.

The front fenders are relatively simple being a single sheet of steel that just needs to be cut up a little higher to make adequate room and repainted.   The rears however are much more involved as you will see.  Here is a picture of the original factory rear “surfline” fenders.

Nissan_Skyline_C111_2000_GTX-E_002

Quite a difference from the GT-R rear fenders shown here.

11_19_09 038

Upon removal of the old flares I had noticed that it looked like someone had previously made an attempt to modify the rear fenders but for some reason decided not to cut them up high enough, resulting in the factory fender being visible underneath the flare.  After removing some mystery goop I uncovered the initial attempt…

10_9_09 085

This would have been much easier if I was starting with an unmolested fender, but what fun would that be?  I had to first start by grinding off all of the rivets that previously held the inner fender well and quarter panel together.  The next step was to draw the line that would be the new fender line and cut it.  The line above the cut shows where the new flare will be.  Remember, the goal here is to make as much room as possible for some wider, low offset wheels.

10_9_09 095

After cutting the quarter panel you can see how big of a gap it creates between the fender well.

10_9_09 101

The next step can be done a couple of different ways depending on what you are looking to achieve.  The metal from the quarter panel can either be bent down into the fender well, or vice versa.  I decided to bend the metal from the fender well up to meet the  quarter panel in this situation as the new flare would cover where the two meet and this would give us a much better finish inside the fender well.

By using a mallet and a fender roller I am able to bend the fender well up and out enough to meet the quarter panel and hold it in place while it gets tack welded.  Note the aluminum in between the wheel on the fender roller and the fender well to prevent the wheel from being melted in the welding process.

10_9_09 104

Make sure to move around the fender as much as possible when making the welds because the last thing you want to do is warp the entire quarter panel from putting too much heat in one spot.  I also used a wet rag to assist in the cooling process to be sure.  With the majority of tack welds done you can now cut off the excess material.

10_9_09 105

After finishing up the welds we decided to go the extra mile and fill in any remaining gaps with seam sealer similar to what is used in new cars in place of spot welds.  The idea here is to strengthen the bond between the fender well and the quarter panel  to retain as much rigidity as possible in the chassis.  After that I used some silicone sealant inside the quarter panels which required removing the interior panels inside the cabin and in the trunk to get full access.  The last thing you want is for water to get inside only to be trapped and eventually turn to rust.

10_9_09 129

And this is what’s left after re modifying the fenders.

10_9_09 158

Now if you just paint the new flares without prepping them properly it will definitely show in the final product.  So for our next installment we will prep and paint the new flares, grill, and front spoiler before they find their new home on the Kenmeri in part 4.

More Posts

1 comment

  • Danny Rodriguez: September 20, 2018

    Your talents and skills are truly amazing. Attention to detail and the passion for authenticity is a pkeasure to see. I am a true admirer of your work. Peace…

    Danny

Leave a comment

All blog comments are checked prior to publishing

Search our store